Vci-100 1.4 (hd) firmware upgrade

[Mudo]

...

Firmware update will work with Spin/typhoon?


Thanks.

...

[fullenglishpint]

Firmware update will work with Spin/typhoon?

I very much doubt it.

[photojojo]

...

Firmware update will work with Spin/typhoon?


Thanks.

...

I doubt it as well since it's VCI firmware.

[Francisco A. Norder]

i have a problem.

Setup:
Renesas Flash Toolkit 4.05 (this version show a new screen)
O.S Win 7 64 bits
Serial to serial cable
when a turn on button vci all lights on.

Clock Frequency (External) = 24.0000MHz, Clock Mode = 0, CKM = 1, and CKP = N/A
Connecting to device 'H8/3052F' on 'COM1'
Configuration:
'BOOT Mode' connection - using emulated interface
Opening port 'COM1' ...
Loading Comms DLL
Loaded Comms DLL
Initiating BOOT SCI sequence
Attempting 9600
Attempting 4800
Attempting 2400
Attempting 1200
Error No 15024: Boot failed

Thanks for help

[photojojo]

The two most common things that fix these problems are to change the port n Renases and to adjust the delay in the advancesetup.exe file that installed along with Renases.

Go through these threads for more info

http://www.djtechtools.com/forum/showthread.php?t=871
http://www.djtechtools.com/forum/showthread.php?t=846

[STYLUS]

just upgraded to 1.4
i liked the previous filter knob sound better
what happened?
how can i change it to a more formant filter type sound on the knob?

[midifidler]

@STYLUS you choose the filter type under the mixer settings

[vbone]

Hopefully I can explain my problems without sound too stupid. So after testing fw 1.3 and 1.4, I found the following.

- 1.3 - I can revert back to 1.2 with full control.
- 1.4 - I can not revert back to 1.2. My pitch faders are completely inoperative. They do not respond to any movement from my vci.

- 1.4 with the matching tsi, my pitch sliders do not move throughout the full range in traktor. The movement of the pitch slider is very minute.

As I previously stated, I would like to be able to revert back to 1.2 to use VDJ for video's.

Maybe there's something I'm missing. Thanks

[photojojo]

- 1.4 with the matching tsi, my pitch sliders do not move throughout the full range in traktor. The movement of the pitch slider is very minute.

It's just visual you still get the full range. If you want to see the full range of movement you'll have to edit the tsi.

I wrote this before 1.4 so there's a chance something's changed

Click on the big gear logo in the upper right corner to get to the preference pane, then click on the controller manager section inside the preference pane. Once your in the controller manager and click on the control column to sort it by name. Find the tempo controls, should be 12 of them, and change the rotary sensitivity to 100% in all of them. You can double click on the number and type 100 in.

Next go to the Transport section of the preference pane and click on reset pitch range 8%. You can choose one of the other ranges here, but you'll lose sensitivity.

The problem with this is that if you have songs with a bigger discrepency that 8% between the BPM's you won't be able to sync them until you get the BPM"s in that range.

- 1.4 - I can not revert back to 1.2. My pitch faders are completely inoperative. They do not respond to any movement from my vci.

As I previously stated, I would like to be able to revert back to 1.2 to use VDJ for video's.

Maybe there's something I'm missing. Thanks

Have you tried re-flashing the 1.4 firmware? I've tested booting into 1.2 from 1.4 and it works for me.

[ivantodorov]

I'm experiencing the following strange behaviour, wondering if it is just me:

1) Play Button doesn't toggle between play and pause. Always Plays from the start of the song

2) When I Press and Hold CUE the song starts playing. I used to be able to press PLAY at the same time to continue playing the song. Instead pressing PLAY while holding down CUE starts the song over from the original que point.

Is this normal?