Classic DJ Weapons of Yore: The BCR 2000

What’s the most searched MIDI controller on Google? The answer might surprise you. It’s not a studio mainstay like the MPC or Trigger Finger. It’s not a relatively new controller or a futuristic, buzz-worthy device. Nope. It’s an unassuming collection of encoders that’s been on the market for the better part of a decade.  Is it worthy of a spot in your arsenal of gear? And, if you already own one, how can you make the most of it?


These days barely a week goes by without a new MIDI controller hitting the market. But back in 2004, Behringer had much less competition when it rolled out the BCR2000. Designed as a companion controller with the BCF2000 (a bank of motorized faders), it quickly caught on with electronic musicians, producers, and DJs.

Nearly eight years later, the BCR’s popularity endures. In production studios and on major tours – a pair of BCR’s were part of Daft Punk’s badass pyramid set-up on their Alive 2007 tour – the controller has quietly become a staple of electronic music.


Let’s take a quick look at the pros and cons of this time-tested MIDI tank, then dig deeper into some of its uses in the studio and on the stage. As we’ll see, there are some good reasons why the BCR’s use is so widespread.


  • Versatile – Eight columns of endless encoders is never a bad thing. But what really makes the BCR stand out is the top row of encoders. Using its four bank buttons, you can have those eight top knobs control 32 different parameters. Combined with an array of buttons (including the top eight knobs, which also have a push function), the control possibilities are endless.
  • Cheap – A new BCR will set you back $150. Look around on Craigslist or eBay, and you can find a used one for closer to $100.
  • Reliable – While it’s not built like the proverbial brick shithouse, the BCR can definitely take a beating. And if it does succumb to a spilled beer or steep drop, it’s not hard to replace.


  • Bulky – Weighing in at about five pounds and taking up a sizeable footprint, this is not a travel-friendly device. It’s not sleek and sexy – especially compared to modern controllers.
  • It doesn’t feel like a DJ mixer – The larger size and looser feel of the knobs is a far cry from the smaller, rubberized feel of most mixers. This might be a concern if you’re mixing “in the box,” and want your controller to feel like a mixer. Also, because the knobs are endless, you can’t feel where they stop and end.
  • Holy crap that’s a lot of knobs The BCR might be overkill if you’re looking to keep it simple; there are more streamlined controllers that might better suit your needs. And if you absolutely must have faders (or a crossfader), there are none to be found here.


One look at the BCR, and you can easily visualize some natural MIDI mappings for studio work. With its eight columns of knobs, it’s logical to assign each column to a track. I like to assign the second row of encoders to the volume of each track, with the third and fourth rows assigned to reverb and delay sends. The pair of buttons on each column can then be assigned to solos and mutes.

The top bank of encoders can be designed around your more specific needs. For instance, you could have each of those four banks control a different FX rack in Ableton. They can also be assigned to various mixer effects, like frequency controls, volume, crossfade, and cueing. Having this much hands-on control is a big help when it comes to things like fine-tuning a mix or adding natural-sounding FX and volume automations to your songs.

To customize your controller settings (MIDI channels, button behavior, etc.), you can try Behringer’s own editor software at your own risk. A more straightforward, easy-to-use editor can be found here.


Live performance is where this thing really shines. If you want to mix up to eight channels at once, the BCR is a solid option. The intuitive eight-column design makes it easy to see what you’re doing. (For you Ableton cats, you can try setting up the Mackie Emulation with the BCR. I find the eight-channel mapping to be a lot more intuitive, especially on stage.)

Granted, stem-mixing eight channels is a lot to handle. If you want to take a more streamlined approach and use just four channels (say, drums, bass, lead, and vocals), you’ve suddenly freed up half the controller for other uses. The red LED’s are also easy to see in a dark club – and they look pretty sweet too.

For a DJ-centric approach, programs like Traktor and Serrato can be mapped to get the job done (check out the DJTT forums for more resources; this post has specialized Traktor mappings). This makes the BCR a cheaper alternative to controllers like the Kontrol X1. But again, the lack of typical mixer knobs and faders could be a deal-breaker if you’re aiming for a traditional DJ controller.


So is the BCR2000 still a smart buy despite its age? And is it right for you? If you fall into one or more of these categories, I’d say it’s definitely worth your attention.

You’re a beginner who’s looking for your first MIDI controller. Simply put, this is a very cheap and easy way to start controlling your audio software.

You need a knob controller for live performance. As I mentioned above, the BCR is a good option for gigs – especially if you want to control several channels of audio at the same time.

You already have a pad controller. The BCR is an awesome companion to pad controllers like the Launchpad, MPC, and Trigger Finger. For example, you can hammer out beats or trigger clips with your right hand, while using the BCR’s knobs to tweak filter sweeps and FX with your left hand. This makes for a more involved live performance – more fun for you, and more entertaining for the crowd.

You’re on a budget. In this craptastic economy, it’s important to remember that you don’t need the latest and greatest gear to make awesome music. Save up a hundred bucks, buy a used BCR (or something similar), and start kicking ass.


A few tips as far as using the BCRs – first, they come from the factory with a slight birth defect: the LEDs respond a bit sluggishly as you turn the knobs. This could be a problem if you want to perform super-fast knob tweaks. However, this can be fixed by following these steps. Some BCR users have also had luck using the latest firmware to customize knob speed.

The BCR is also a good option for live visuals. VJ’s have been using it for years, in combination with one of many VJ programs, to bombard retinas with dynamic images.

Additionally, I’ve used the terms “knobs” and “encoders” interchangeably in this article, but there are some important differences. As mentioned above, knobs have physical start and end points whereas endless encoders don’t. On the other hand, there’s a big advantage to having endless encoders: their position moves automatically as you switch between banks and presets.

Finally, it’s worth noting that if you prefer to use hardware over software (the way old school Live PA’s used to do it), don’t forget that the BCR can also be used to send MIDI commands to other devices.

3000BCRcontrollerDownloadFixhow toReview
Comments (31)
Add Comment
  • DeLorianRoyal

    It’d be rad if we could get the option to post midi mappings for the BCR on the website.

  • nulloid

    I’ve had a BCR for what seems like forever and while it did take a backseat to my APC and Maschine I’ve recently brought it out of retirement and it is still an amazing piece of kit. My only gripe would be that it requires it’s own power source rather than being USB powered.

  • julien

    Thx for this precious article, I was about to buy it to modify it for my dj use.
    But, due to endless knobs, do you think i can replace them with non-endless knobs ?


  • Weslochan

    HAI thank you for giving the BCR credit 

  • Tristan McCool

    I saw Breakbot playing a BCR2000 about 5 years ago in Brisbane, it made me want to get one since then on.

  • Hugo Amiguinho

    I have one for a few years ago. but now I have a problem in one encoder. It is not working well in traktor pro, I rotate the encoder but his response is very slow. I think the problem is in the hardware. Can someone help me and give me some information how can i open properly  the BCR2000 and fix the encoders. thank you very much

    • Pablo Fullana

      hey Hugo, hope you are doing fine. I’m having the same issue. I’ve just one encoder that started to work slower than the rest and, besides, the values it s sending are not “correlated” -like if I was moving it forward and backwards as well. Not sure if you get what I am trying to explain here, it’s not that easy to describe it. Anyway,have you been able to fix the issue you had? Thanks in advance!

  • 9b0

    i really luv it:

  • Imagine Music

    Thanks for the insightful review, Kent!  (And thanks everyone for the comments!) We’ve also see Tim Exile doing some of his Native Instruments videos using the BCR2000 or BCF2000.

  • Sol

    I’m also using a BCR and a BCF for almost 3 years now.
    I love its versatile usage scenarios.
    For instance, I use the BCF in Mackie Mode for Ableton Live 8.
    For Traktor i have the BCF and BCR (daisy chained via MIDI cable) to control 4 decks.
    Wish i had more time to do more complex midi mappings.

  • Aaron Lamb

    Been using a BCF for years and these might have been about the best thing Berhinger ever sold

  • Brodyism

    I’ve never used the BCR or BCF but I have been using a BCD-3000 for a few years now with no problems at all. The built in soundcard is decent (I prefer my audio 4 however) and although the encoders are not as tight as the S4 they respond instantly and accurately. It has flown around the world with me stuffed in a backpack, jammed into tight dj booths, dropped multiple times and still works perfectly to this day. A great cheap solution, I paid less than $200 for it brand new. I’ve worked out a pretty good mapping with modifiers that allows for full effects control, key, filter, full eq, loop+set/size, cue, move etc. HIt me up through if you want the .tsi

  • Argos

    i have one….

    the thing rocks….

  • Sam

    I have been using my Brc for a year and a bit now. If u know how to program it properly the worlds your oyster. Mine ha fallen off stage, had beer tipped all over it and copped savage beatings when I travel with it. It still works every time. How ever I have the problem of triggering a knob which accidently triggers the movement of another knob. This can be a disaster if the second knob happens to be track volume. Does anyone know if I can fix it with out re routing the whole controller?

  • Arubaro

    Ooopos, i forget the video: me using it

    • Leslie Jones

      Here’s pics of us, using it at the first MIDIfight Club. 😉

  • Arubaro

    This article goes to mi favs heaven. The BCR was my first controller and i’ll always love it.

  • MrAybar

    The link stated in the article for traktor mapping is not working!!! 

    • Spacecamp

      Hmm, strange. It should work fine now! 

  • Leslie Jones

    w00t! Finally someone else who also dares to give the BCR the proper credit it deserves.

  • Ogama8

    How do y’all feel this compares to the new A&H K2?

  • Jeffone

    I had a BCF for years and it’s still going strong…certainly more durable than the various other cheap midi controllers I’ve owned. The BCF drivers and third-party editors are solid. The fader motors can be annoying, but all you have to do is disable them. A highly underrated line of products…

  • Chris Blarsky

    Great for VST tweaking!
    Plus you can save several presets to match them.

  • Lewisjprichardson

    I pretty sure this is the controller this guy is using but it’s sometimes hard to see

    • Earsfilled


  • Jorge Lulo

    I think the APC40, came up with a better offer than the BCR, i love encoder because when I create a midi mapping it expand my possibilities.

  • Tom

    I used a BCR -mainly for VJing- quite a few years, I definitely enjoyed the flexibility and sheer mass of knobs and buttons (the four programmable banks are also a killer feature which I am really missing in my current setup) but finally gave up on it, because it’s latency was plain terrible. Maybe newer models/firmware are better here, but I have generally been avoiding endless controllers since then. I’ve talked to a lot of collegues and most of them shared my experiences with endless encoders.


    use them to this day!

  • D Holling


  • Dreamr O'Kelly

    The BCR and BCF are fundamental to my production. And I’ve yet to find a better “Knob Box” anywhere for DJing.The LED feedback ROCKS for night gigs.