Five Tips and Tricks for Using the Midi Fighter Twister With Ableton Live

When preparing your set for a live performance, there are a lot of exciting options that both Ableton and your MIDI controller provide you—and sometimes it can be difficult to know where to start. Today we show you five great tips and tricks for using the Midi Fighter Twister and Ableton to perform live.

1. Push-and-Turn Looping Effects
These effects utilize a beat-repeat device that is turned on via the push switch on the Twister to catch short loops at 1/2, 1/4, 1/8, and 1/16 notes. Then the encoder turn is used to apply several other effects post-loop. This allows for creative on-the-fly loop-catching and then further processing.

2. Using the Twister Super Knob Functionality

The super-knob is a feature built into the Twister firmware and it allows you to be able to send two control changes from one encoder. Imagine an encoder that sends a control change message when you start to turn it and then when you turn past a certain point on the encoder it sends a second CC to control a different parameter.

I’ve set this up so that the turn of the encoder increases the decay time on the reverb on a return track. Then the same encoder with super-knob functionality controls a high-pass filter and delay but only engages after the knob has been turned past 3 o’clock.

3. Using the Center Detent on the Twister
When using EQ and Filters in a digital environment, I prefer that theEQ’s default position is in the center or has a MIDI value of 64. This is to replicate how analog DJ mixers function.

If the center detent is enabled in the Twister Utility Software, the encoder will behave like a potentiometer with a center detent. This means the LED is in the middle and indicates that you are at a default position with a MIDI value of 64. To utilize the center detent position, you will need to download this special EQ and Filter rack, which is set up so the default device values are in the center position also.

4. Navigation and Scene Launching
The Twister’s side buttons can do many things. I’ve been using them for navigating and launching scenes. Hit Command+M in Ableton to go into MIDI-map mode and then select the “relative session mappings” section and map the side buttons accordingly to be able to launch and navigate scenes.

The Twister also has four banks or levels for the encoders, which are accessed via the middle side buttons. Essentially the Twister has 16 physical encoders but with these bank buttons it has 64, or four banks of 16.

5. The Built-In Twister Sequencer
One of the most exciting things about the Twister is that it has its own built-in sequencer. To enter the sequencer mode, hit both of the middle side buttons at the same time. The top two rows of encoders are dedicated to the separate voices or sounds. As you turn each knob it engages a pattern for that sound which increases in complexity the farther you turn it. If you hit one of the push switches for a voice, you will jump to a separate page where you can program patterns manually into the sequencer.

Now you’ve five techniques for setting up the Twister to start using it in Ableton. The included racks can be downloaded here, and remember: These techniques can be applied to many other controllers and performance setups.

Midi Fighter Twisters are now $199 in the DJTT webstore here.

Find me here for more Ableton tips and tricks, and let us know what else you’d like to see in the comments below.

Abletonableton livecenter detentencoderslenny kiserMidi Fightermidi fighter twisterscene launchingsequencerTutorial
Comments (16)
Add Comment
  • Kanou Fabien

    Hello LENNY How to use two DJ TechTools Twister Fighter in Ableton Live, without it coming into conflict ?
    thanks you for your answer.

  • Morten Folmer Nielsen

    So how did you set it up so that the default device values are in the center position?

  • Will Gray

    I’m confused, where is the ableton set ( the link only has “LK – TWISTER – LOOPER FX.adg” and “CENTER DETENT EQ.adg” ) I just bought a twister and trying to figure out how to use. having the set for this tutorial would be very helpful. i’m new to this and it’s bit hard to figure out for someone at my level.

  • demetriusb

    Links are broken.

    • Matías J. Padilla

      Links are working now

  • b1kjsh

    hmm… what happened to this post… it looks like the links are broken to the included ableton set…

    • Matías J. Padilla

      Links are working now =)

      • b1kjsh

        Awesome thanks!

  • chris

    don’t drink and drive, and don’t do any day without an lol.
    btw: yesterday, it was full moon and friday the 13, and i’m still alive

      • chris


        …hello, is there any body out there?

        i’m only with some freak here

  • JohnLElkins

    Then the encoder turn is used to apply several other effects post-loop. This allows for creative on-the-fly loop-catching and then further processing.

  • Onno Kaell

    Are those “regular” Chroma Caps Encoder Knobs” that are used on the Midifighter Twister?
    If so – PLEASE start selling those WHITE ones in your webstore!!!

    • Matías J. Padilla

      Yes they are =). They are called Grey (it’s a very light shade of grey, pure white gets dirty too easily)

      • Onno Kaell

        As I do own the “grey” ones and they look totally different to me I contacted DJ Techtools and they told me that those indeed are “all white” ones!